Reusable Self-Adhesive Hook and Loop Tape in stock colours. Woven hook and loop, samples in 7 days, MOQ 500 m.
| Material | Nylon |
| Adhesive | Acrylic |
| Construction | Self-Adhesive Hook and Loop Tape |
| MOQ | 500 m stock colour / 3,000 m dyed |
| Minimum order | 500 m stock colour / 3,000 m dyed |
Not ready to ask for a price? Just ask a question — an engineer replies, not a sales script.
| Material | Nylon |
|---|---|
| Adhesive | Acrylic |
| Construction | Self-Adhesive Hook and Loop Tape |
| MOQ | 500 m stock colour / 3,000 m dyed |
| Minimum order | 500 m stock colour / 3,000 m dyed |
| Production lead time | 2-3 weeks after sample approval |
| Packing | Poly bag + carton, palletised for LCL |
| Certification | REACH, RoHS; OEKO-TEX on request |
Same build, different width or length. Mixed sizes in one carton are fine.
| Size | Colour | MOQ |
|---|---|---|
| 500 m stock colour / 3,000 m dyed | ||
| 500 m stock colour / 3,000 m dyed | ||
| 10 mm | Black | 500 m stock colour / 3,000 m dyed |
| 12 mm | Black | 500 m stock colour / 3,000 m dyed |
| 16 mm | Black | 500 m stock colour / 3,000 m dyed |
Send a drawing and we will confirm tooling cost and tolerance before you commit.
Talk to an engineerSelf-adhesive hook and loop tape with a pressure-sensitive backing, 10-150 mm wide in a stock colour. The liner is slit through the middle so the roll can be applied without the backing tearing across the web. Stock widths are slit in one millimetre steps, so the size on your drawing is normally a slitting instruction rather than a new tool. Tell us the width and the put-up and the quote is against a stock construction.
It is used for display mounting, exhibition graphics, cable management pads, and removable covers on machinery. Twenty-four hours at room temperature gives full strength; a pull test done twenty minutes after application reads 55 to 65 percent of final and is not a valid reject criterion.
Width, colour and put-up are set per order, so a mixed carton is normal rather than an exception. Minimum order is 500 m stock colour / 3,000 m dyed, and the master roll exists after the first run, which means a repeat order on the same construction does not add lead time.
The put-up matters as much as the width. A 25 m roll on a 38 mm core will not fit a mandrel built for 76 mm cores, and a kiss-cut part packed flat behaves differently on a dispenser than the same part wound on a roll.
Colour is matched to a retained standard under D65, not to a screen. Metamerism is real: a black that matches under office light can read green under daylight, which is why the approved standard is a physical swatch rather than a photograph.
Liner-backed goods are packed flat rather than on a core where the part is kiss-cut, because a tight wind puts a set into the liner and the parts lift at the edges on the applicator.
If the width is not settled, send the drawing or the part it has to hold and we will suggest the narrowest width that does the job. Narrower is cheaper and follows a radius better; wider only helps where a large flat face has to stay down.
The adhesive decides whether this product works, not the hook. Clean and dry the surface, apply with a roller at roughly 10 N/cm², and leave it 24 hours before loading — peel measured immediately after application reads about 60% of its final value. On polypropylene, polyethylene or heavy powder coat, test a sample first or specify the rubber version.
At 25 mm this construction is normally specified for furniture trim, panel fixing, mid-weight strap assemblies and equipment covers. The width does not change the peel per unit width much, but narrower tape engages fewer hooks at the edge, which is where peeling starts — so if the joint opens repeatedly, go up one width rather than up one grade.
Powder coat usually works with the heavy-tack acrylic, applied with firm roller pressure. Polypropylene and polyethylene have very low surface energy and are the most common field failure — test a sample on the actual substrate before production, or ask us to quote the rubber adhesive version.
Twenty-four hours at room temperature for full strength. Peel measured twenty minutes after application is typically 55–65% of the final value, so a QC pull test done straight off the line will always read low and is not a valid reject criterion.
Minimum order for this item is 500 m stock colour / 3,000 m dyed. Production runs 2–3 weeks after sample approval, with samples typically shipped in 7 days.
Self-Adhesive Hook and Loop
Self-Adhesive Hook and Loop Tape, Price Friendly
Self-Adhesive Hook and Loop Tape in stock colours. Woven hook and loop, sample...
MOQ 500 m stock colour / 3,000 m dyed
Self-Adhesive Hook and Loop
Waterproof Self-Adhesive Hook and Loop Tape
Waterproof Self-Adhesive Hook and Loop Tape in stock colours. Woven hook and l...
MOQ 500 m stock colour / 3,000 m dyed
Self-Adhesive Hook and Loop
12 mm Elastic Self-Adhesive Hook and Loop Tape, Black
Elastic Self-Adhesive Hook and Loop Tape at 12 mm in Black. Woven hook and loo...
MOQ 500 m stock colour / 3,000 m dyed
Self-Adhesive Hook and Loop
Heavy-Duty Self-Adhesive Hook and Loop Tape, Nylon
Heavy-Duty Self-Adhesive Hook and Loop Tape in stock colours. Woven hook and l...
MOQ 500 m stock colour / 3,000 m dyed